9 files changed, 250 insertions, 158 deletions

diff --git a/.travis.yml b/.travis.yml
index aa1001a..21a9ca6 100644
--- a/.travis.yml
+++ b/.travis.yml
@@ -32,7 +32,7 @@ cache:
 
 env:
   - PLATFORMIO_CI_SRC=examples/Single_Shot/Single_Shot.ino
-  - PLATFORMIO_CI_SRC=examples/Continous/Continous.ino
+  - PLATFORMIO_CI_SRC=examples/Continuous/Continuous.ino
   - PLATFORMIO_CI_SRC=examples/Alert_Window_Mode/Alert_Window_Mode.ino
 
 install:
diff --git a/examples/Alert_Window_Mode/Alert_Window_Mode.ino b/examples/Alert_Window_Mode/Alert_Window_Mode.ino
index 3be5dec..a68b684 100644
--- a/examples/Alert_Window_Mode/Alert_Window_Mode.ino
+++ b/examples/Alert_Window_Mode/Alert_Window_Mode.ino
@@ -81,14 +81,14 @@ void setup() {
    */

   //adc.setConvRate(ADS1115_8_SPS); //uncomment if you want to change the default

 

-  /* Set continous or single shot mode:

+  /* Set continuous or single shot mode:

    * 

-   *  ADS1115_CONTINOUS  ->  continous mode

-   *  ADS1115_SINGLE     ->  single shot mode (default)

+   *  ADS1115_CONTINUOUS  ->  continuous mode

+   *  ADS1115_SINGLE      ->  single shot mode (default)

    */

-  adc.setMeasureMode(ADS1115_CONTINOUS); //comment or change you want to change to single shot

+  adc.setMeasureMode(ADS1115_CONTINUOUS); //comment or change you want to change to single shot

 

-   /* Choose maximum limit or maxium and minimum alert limit (window)in Volt - alert pin will 

+   /* Choose maximum limit or maximum and minimum alert limit (window)in Volt - alert pin will 

    *  be active when measured values are beyond the maximum limit or outside the window 

    *  Upper limit first: setAlertLimit_V(MODE, maximum, minimum)

    *  In max limit mode the minimum value is the limit where the alert pin will be deactivated 

diff --git a/examples/Alert_Window_Mode_with_Latch/Alert_Window_Mode_with_Latch.ino b/examples/Alert_Window_Mode_with_Latch/Alert_Window_Mode_with_Latch.ino
index 049a65f..f90d6db 100644
--- a/examples/Alert_Window_Mode_with_Latch/Alert_Window_Mode_with_Latch.ino
+++ b/examples/Alert_Window_Mode_with_Latch/Alert_Window_Mode_with_Latch.ino
@@ -83,14 +83,14 @@ void setup() {
    */

   //adc.setConvRate(ADS1115_8_SPS); //uncomment if you want to change the default

 

-  /* Set continous or single shot mode:

+  /* Set continuous or single shot mode:

    * 

-   *  ADS1115_CONTINOUS  ->  continous mode

+   *  ADS1115_CONTINUOUS  ->  continuous mode

    *  ADS1115_SINGLE     ->  single shot mode (default)

    */

-  adc.setMeasureMode(ADS1115_CONTINOUS); //comment or change if you want to change single shot

+  adc.setMeasureMode(ADS1115_CONTINUOUS); //comment or change if you want to change single shot

 

-   /* Choose maximum limit or maxium and minimum alert limit (window)in Volt - alert pin will 

+   /* Choose maximum limit or maximum and minimum alert limit (window)in Volt - alert pin will 

    *  be active when measured values are beyond the maximum limit or outside the window 

    *  Upper limit first: setAlertLimit_V(MODE, maximum, minimum)

    *  In max limit mode the minimum value is the limit where the alert pin will be deactivated 

diff --git a/examples/Continous/Continous.ino b/examples/Continuous/Continuous.ino
index bece321..3c8313a 100644
--- a/examples/Continous/Continous.ino
+++ b/examples/Continuous/Continuous.ino
@@ -1,129 +1,129 @@
-/***************************************************************************

-* Example sketch for the ADS1115_WE library

-*

-* This sketch shows how to use the ADS1115 in continous mode. 

-*  

-* Further information can be found on:

-* https://wolles-elektronikkiste.de/ads1115

-* 

-***************************************************************************/

-

-#include<ADS1115_WE.h> 

-#include<Wire.h>

-#define I2C_ADDRESS 0x48

-

-ADS1115_WE adc(I2C_ADDRESS);

-// ADS1115_WE adc = ADS1115_WE(); // Alternative: uses default address 0x48

-

-void setup() {

-  Wire.begin();

-  Serial.begin(9600);

-  if(!adc.init()){

-    Serial.println("ADS1115 not connected!");

-  }

-

-  /* Set the voltage range of the ADC to adjust the gain

-   * Please note that you must not apply more than VDD + 0.3V to the input pins!

-   * 

-   * ADS1115_RANGE_6144  ->  +/- 6144 mV

-   * ADS1115_RANGE_4096  ->  +/- 4096 mV

-   * ADS1115_RANGE_2048  ->  +/- 2048 mV (default)

-   * ADS1115_RANGE_1024  ->  +/- 1024 mV

-   * ADS1115_RANGE_0512  ->  +/- 512 mV

-   * ADS1115_RANGE_0256  ->  +/- 256 mV

-   */

-  adc.setVoltageRange_mV(ADS1115_RANGE_6144); //comment line/change parameter to change range

-

-  /* Set the inputs to be compared

-   *  

-   *  ADS1115_COMP_0_1    ->  compares 0 with 1 (default)

-   *  ADS1115_COMP_0_3    ->  compares 0 with 3

-   *  ADS1115_COMP_1_3    ->  compares 1 with 3

-   *  ADS1115_COMP_2_3    ->  compares 2 with 3

-   *  ADS1115_COMP_0_GND  ->  compares 0 with GND

-   *  ADS1115_COMP_1_GND  ->  compares 1 with GND

-   *  ADS1115_COMP_2_GND  ->  compares 2 with GND

-   *  ADS1115_COMP_3_GND  ->  compares 3 with GND

-   */

-  adc.setCompareChannels(ADS1115_COMP_0_GND); //comment line/change parameter to change channel

-

-  /* Set number of conversions after which the alert pin will be active

-   * - or you can disable the alert 

-   *  

-   *  ADS1115_ASSERT_AFTER_1  -> after 1 conversion

-   *  ADS1115_ASSERT_AFTER_2  -> after 2 conversions

-   *  ADS1115_ASSERT_AFTER_4  -> after 4 conversions

-   *  ADS1115_DISABLE_ALERT   -> disable comparator / alert pin (default) 

-   */

-  //adc.setAlertPinMode(ADS1115_ASSERT_AFTER_1); //uncomment if you want to change the default

-

-  /* Set the conversion rate in SPS (samples per second)

-   * Options should be self-explaining: 

-   * 

-   *  ADS1115_8_SPS 

-   *  ADS1115_16_SPS  

-   *  ADS1115_32_SPS 

-   *  ADS1115_64_SPS  

-   *  ADS1115_128_SPS (default)

-   *  ADS1115_250_SPS 

-   *  ADS1115_475_SPS 

-   *  ADS1115_860_SPS 

-   */

-  // adc.setConvRate(ADS1115_8_SPS); //uncomment if you want to change the default

-

-  /* Set continous or single shot mode:

-   * 

-   *  ADS1115_CONTINOUS  ->  continous mode

-   *  ADS1115_SINGLE     ->  single shot mode (default)

-   */

-  adc.setMeasureMode(ADS1115_CONTINOUS); //comment line/change parameter to change mode

-

-   /* Choose maximum limit or maxium and minimum alert limit (window)in Volt - alert pin will 

-   *  be active when measured values are beyond the maximum limit or outside the window 

-   *  Upper limit first: setAlertLimit_V(MODE, maximum, minimum)

-   *  In max limit mode the minimum value is the limit where the alert pin will be deactivated (if 

-   *  not latched)  

-   * 

-   *  ADS1115_MAX_LIMIT

-   *  ADS1115_WINDOW

-   * 

-   */

-  //adc.setAlertModeAndLimit_V(ADS1115_MAX_LIMIT, 3.0, 1.5); //uncomment if you want to change the default

-  

-  /* Enable or disable latch. If latch is enabled the alarm pin will be active until the

-   * conversion register is read (getResult functions). If disabled the alarm pin will be

-   * deactivated with next value within limits. 

-   *  

-   *  ADS1115_LATCH_DISABLED (default)

-   *  ADS1115_LATCH_ENABLED

-   */

-  //adc.setAlertLatch(ADS1115_LATCH_ENABLED); //uncomment if you want to change the default

-

-  /* Sets the alert pin polarity if active:

-   *  

-   * Enable or disable latch. If latch is enabled the alarm pin will be active until the

-   * conversion register is read (getResult functions). If disabled the alarm pin will be

-   * deactivated with next value within limits. 

-   *  

-   * ADS1115_ACT_LOW  ->  active low (default)   

-   * ADS1115_ACT_HIGH ->  active high

-   */

-  //adc.setAlertPol(ADS1115_ACT_LOW); //uncomment if you want to change the default

- 

-  /* With this function the alert pin will be active, when a conversion is ready.

-   * In order to deactivate, use the setAlertLimit_V function  

-   */

-  //adc.setAlertPinToConversionReady(); //uncomment if you want to change the default

-

-  Serial.println("ADS1115 Example Sketch - Continous Mode");

-  Serial.println();

-}

-

-void loop() {

-  float voltage = 0.0;

-  voltage = adc.getResult_V(); // alternative: getResult_mV for Millivolt

-  Serial.print("Channel 0 vs GND [V]: ");

-  Serial.println(voltage);

-  Serial.println("-------------------------------");

-  delay(2000);

-}

+/***************************************************************************
+* Example sketch for the ADS1115_WE library
+*
+* This sketch shows how to use the ADS1115 in continuous mode. 
+*  
+* Further information can be found on:
+* https://wolles-elektronikkiste.de/ads1115
+* 
+***************************************************************************/
+
+#include<ADS1115_WE.h> 
+#include<Wire.h>
+#define I2C_ADDRESS 0x48
+
+ADS1115_WE adc(I2C_ADDRESS);
+// ADS1115_WE adc = ADS1115_WE(); // Alternative: uses default address 0x48
+
+void setup() {
+  Wire.begin();
+  Serial.begin(9600);
+  if(!adc.init()){
+    Serial.println("ADS1115 not connected!");
+  }
+
+  /* Set the voltage range of the ADC to adjust the gain
+   * Please note that you must not apply more than VDD + 0.3V to the input pins!
+   * 
+   * ADS1115_RANGE_6144  ->  +/- 6144 mV
+   * ADS1115_RANGE_4096  ->  +/- 4096 mV
+   * ADS1115_RANGE_2048  ->  +/- 2048 mV (default)
+   * ADS1115_RANGE_1024  ->  +/- 1024 mV
+   * ADS1115_RANGE_0512  ->  +/- 512 mV
+   * ADS1115_RANGE_0256  ->  +/- 256 mV
+   */
+  adc.setVoltageRange_mV(ADS1115_RANGE_6144); //comment line/change parameter to change range
+
+  /* Set the inputs to be compared
+   *  
+   *  ADS1115_COMP_0_1    ->  compares 0 with 1 (default)
+   *  ADS1115_COMP_0_3    ->  compares 0 with 3
+   *  ADS1115_COMP_1_3    ->  compares 1 with 3
+   *  ADS1115_COMP_2_3    ->  compares 2 with 3
+   *  ADS1115_COMP_0_GND  ->  compares 0 with GND
+   *  ADS1115_COMP_1_GND  ->  compares 1 with GND
+   *  ADS1115_COMP_2_GND  ->  compares 2 with GND
+   *  ADS1115_COMP_3_GND  ->  compares 3 with GND
+   */
+  adc.setCompareChannels(ADS1115_COMP_0_GND); //comment line/change parameter to change channel
+
+  /* Set number of conversions after which the alert pin will be active
+   * - or you can disable the alert 
+   *  
+   *  ADS1115_ASSERT_AFTER_1  -> after 1 conversion
+   *  ADS1115_ASSERT_AFTER_2  -> after 2 conversions
+   *  ADS1115_ASSERT_AFTER_4  -> after 4 conversions
+   *  ADS1115_DISABLE_ALERT   -> disable comparator / alert pin (default) 
+   */
+  //adc.setAlertPinMode(ADS1115_ASSERT_AFTER_1); //uncomment if you want to change the default
+
+  /* Set the conversion rate in SPS (samples per second)
+   * Options should be self-explaining: 
+   * 
+   *  ADS1115_8_SPS 
+   *  ADS1115_16_SPS  
+   *  ADS1115_32_SPS 
+   *  ADS1115_64_SPS  
+   *  ADS1115_128_SPS (default)
+   *  ADS1115_250_SPS 
+   *  ADS1115_475_SPS 
+   *  ADS1115_860_SPS 
+   */
+  // adc.setConvRate(ADS1115_8_SPS); //uncomment if you want to change the default
+
+  /* Set continuous or single shot mode:
+   * 
+   *  ADS1115_CONTINUOUS  ->  continuous mode
+   *  ADS1115_SINGLE     ->  single shot mode (default)
+   */
+  adc.setMeasureMode(ADS1115_CONTINUOUS); //comment line/change parameter to change mode
+
+   /* Choose maximum limit or maximum and minimum alert limit (window)in Volt - alert pin will 
+   *  be active when measured values are beyond the maximum limit or outside the window 
+   *  Upper limit first: setAlertLimit_V(MODE, maximum, minimum)
+   *  In max limit mode the minimum value is the limit where the alert pin will be deactivated (if 
+   *  not latched)  
+   * 
+   *  ADS1115_MAX_LIMIT
+   *  ADS1115_WINDOW
+   * 
+   */
+  //adc.setAlertModeAndLimit_V(ADS1115_MAX_LIMIT, 3.0, 1.5); //uncomment if you want to change the default
+  
+  /* Enable or disable latch. If latch is enabled the alarm pin will be active until the
+   * conversion register is read (getResult functions). If disabled the alarm pin will be
+   * deactivated with next value within limits. 
+   *  
+   *  ADS1115_LATCH_DISABLED (default)
+   *  ADS1115_LATCH_ENABLED
+   */
+  //adc.setAlertLatch(ADS1115_LATCH_ENABLED); //uncomment if you want to change the default
+
+  /* Sets the alert pin polarity if active:
+   *  
+   * Enable or disable latch. If latch is enabled the alarm pin will be active until the
+   * conversion register is read (getResult functions). If disabled the alarm pin will be
+   * deactivated with next value within limits. 
+   *  
+   * ADS1115_ACT_LOW  ->  active low (default)   
+   * ADS1115_ACT_HIGH ->  active high
+   */
+  //adc.setAlertPol(ADS1115_ACT_LOW); //uncomment if you want to change the default
+ 
+  /* With this function the alert pin will be active, when a conversion is ready.
+   * In order to deactivate, use the setAlertLimit_V function  
+   */
+  //adc.setAlertPinToConversionReady(); //uncomment if you want to change the default
+
+  Serial.println("ADS1115 Example Sketch - Continuous Mode");
+  Serial.println();
+}
+
+void loop() {
+  float voltage = 0.0;
+  voltage = adc.getResult_V(); // alternative: getResult_mV for Millivolt
+  Serial.print("Channel 0 vs GND [V]: ");
+  Serial.println(voltage);
+  Serial.println("-------------------------------");
+  delay(2000);
+}
diff --git a/examples/Single_Shot/Single_Shot.ino b/examples/Single_Shot/Single_Shot.ino
index 8a5a198..3b583b2 100644
--- a/examples/Single_Shot/Single_Shot.ino
+++ b/examples/Single_Shot/Single_Shot.ino
@@ -32,7 +32,7 @@ void setup() {
    * ADS1115_RANGE_0512  ->  +/- 512 mV

    * ADS1115_RANGE_0256  ->  +/- 256 mV

    */

-  adc.setVoltageRange_mV(ADS1115_RANGE_6144); //comment line/change paramater to change range

+  adc.setVoltageRange_mV(ADS1115_RANGE_6144); //comment line/change parameter to change range

 

   /* Set the inputs to be compared

    *  

@@ -71,14 +71,14 @@ void setup() {
    */

   //adc.setConvRate(ADS1115_128_SPS); //uncomment if you want to change the default

 

-  /* Set continous or single shot mode:

+  /* Set continuous or single shot mode:

    * 

-   *  ADS1115_CONTINOUS  ->  continous mode

+   *  ADS1115_CONTINUOUS  ->  continuous mode

    *  ADS1115_SINGLE     ->  single shot mode (default)

    */

-  //adc.setMeasureMode(ADS1115_CONTINOUS); //uncomment if you want to change the default

+  //adc.setMeasureMode(ADS1115_CONTINUOUS); //uncomment if you want to change the default

 

-   /* Choose maximum limit or maxium and minimum alert limit (window)in Volt - alert pin will 

+   /* Choose maximum limit or maximum and minimum alert limit (window)in Volt - alert pin will 

    *  be active when measured values are beyond the maximum limit or outside the window 

    *  Upper limit first: setAlertLimit_V(MODE, maximum, minimum)

    *  In max limit mode the minimum value is the limit where the alert pin will be deactivated (if 

diff --git a/examples/Single_Shot_Conv_Ready_Alert_Controlled/Single_Shot_Conv_Ready_Alert_Controlled.ino b/examples/Single_Shot_Conv_Ready_Alert_Controlled/Single_Shot_Conv_Ready_Alert_Controlled.ino
index a02067a..5822f01 100644
--- a/examples/Single_Shot_Conv_Ready_Alert_Controlled/Single_Shot_Conv_Ready_Alert_Controlled.ino
+++ b/examples/Single_Shot_Conv_Ready_Alert_Controlled/Single_Shot_Conv_Ready_Alert_Controlled.ino
@@ -76,14 +76,14 @@ void setup() {
    */

   adc.setConvRate(ADS1115_8_SPS); //comment line/change parameter to change SPS

 

-  /* Set continous or single shot mode:

+  /* Set continuous or single shot mode:

    * 

-   *  ADS1115_CONTINOUS  ->  continous mode

+   *  ADS1115_CONTINUOUS  ->  continuous mode

    *  ADS1115_SINGLE     ->  single shot mode (default)

    */

-  //adc.setMeasureMode(ADS1115_CONTINOUS); // continous mode does not work with conversion ready

+  //adc.setMeasureMode(ADS1115_CONTINUOUS); // continuous mode does not work with conversion ready

 

-   /* Choose maximum limit or maxium and minimum alert limit (window)in Volt - alert pin will 

+   /* Choose maximum limit or maximum and minimum alert limit (window)in Volt - alert pin will 

    *  be active when measured values are beyond the maximum limit or outside the window 

    *  Upper limit first: setAlertLimit_V(MODE, maximum, minimum)

    *  In max limit mode the minimum value is the limit where the alert pin will be deactivated (if 

diff --git a/examples/Single_Shot_Conv_Ready_Controlled/Single_Shot_Conv_Ready_Controlled.ino b/examples/Single_Shot_Conv_Ready_Controlled/Single_Shot_Conv_Ready_Controlled.ino
index 976e682..9ca409e 100644
--- a/examples/Single_Shot_Conv_Ready_Controlled/Single_Shot_Conv_Ready_Controlled.ino
+++ b/examples/Single_Shot_Conv_Ready_Controlled/Single_Shot_Conv_Ready_Controlled.ino
@@ -2,7 +2,7 @@
 * Example sketch for the ADS1115_WE library

 *

 * This sketch shows how you can use the conversion ready bit with the isBusy function.

-* This does not work in the continous mode. 

+* This does not work in the continuous mode. 

 *  

 * Further information can be found on:

 * https://wolles-elektronikkiste.de/ads1115

@@ -72,14 +72,14 @@ void setup() {
    */

   adc.setConvRate(ADS1115_8_SPS); //comment line/change parameter to change SPS

 

-  /* Set continous or single shot mode:

+  /* Set continuous or single shot mode:

    * 

-   *  ADS1115_CONTINOUS  ->  continous mode

+   *  ADS1115_CONTINUOUS  ->  continuous mode

    *  ADS1115_SINGLE     ->  single shot mode (default)

    */

-  //adc.setMeasureMode(ADS1115_CONTINOUS); //continous mode does not work with conversion ready (isBusy)

+  //adc.setMeasureMode(ADS1115_CONTINUOUS); //continuous mode does not work with conversion ready (isBusy)

 

-   /* Choose maximum limit or maxium and minimum alert limit (window)in Volt - alert pin will 

+   /* Choose maximum limit or maximum and minimum alert limit (window)in Volt - alert pin will 

    *  be active when measured values are beyond the maximum limit or outside the window 

    *  Upper limit first: setAlertLimit_V(MODE, maximum, minimum)

    *  In max limit mode the minimum value is the limit where the alert pin will be deactivated (if 

diff --git a/keywords.txt b/keywords.txt
new file mode 100644
index 0000000..8e76357
--- /dev/null
+++ b/keywords.txt
@@ -0,0 +1,91 @@
+#######################################
+# Syntax Coloring Map For ADS1115_WE
+#######################################
+
+#######################################
+# Datatypes (KEYWORD1)
+#######################################
+
+ADS1115_WE	KEYWORD1
+
+# ENUM TYPES
+ADS1115_COMP_QUE	KEYWORD1
+ADS1115_LATCH	KEYWORD1
+ADS1115_ALERT_POL	KEYWORD1
+ADS1115_COMP_MODE	KEYWORD1
+ADS1115_CONV_RATE	KEYWORD1
+ADS1115_MEASURE_MODE	KEYWORD1
+ADS1115_RANGE	KEYWORD1
+ADS1115_MUX	KEYWORD1
+ADS1115_STATUS_OR_START	KEYWORD1
+
+
+#######################################
+# Methods and Functions (KEYWORD2)
+#######################################
+
+reset	KEYWORD2
+init	KEYWORD2
+setAlertPinMode	KEYWORD2
+setAlertLatch	KEYWORD2
+setAlertPol	KEYWORD2
+setAlertModeAndLimit_V	KEYWORD2
+setConvRate	KEYWORD2
+setMeasureMode	KEYWORD2
+setVoltageRange_mV	KEYWORD2
+setCompareChannels	KEYWORD2
+isBusy	KEYWORD2
+startSingleMeasurement	KEYWORD2
+getResult_V	KEYWORD2
+getResult_mV	KEYWORD2
+setAlertPinToConversionReady	KEYWORD2
+clearAlert	KEYWORD2
+
+#######################################
+# Constants (LITERAL1)
+#######################################
+ADS1115_CONV_REG	LITERAL1
+ADS1115_CONFIG_REG	LITERAL1
+ADS1115_LO_THRESH_REG	LITERAL1
+ADS1115_HI_THRESH_REG	LITERAL1
+ADS1115_REG_FACTOR	LITERAL1
+ADS1115_REG_RESET_VAL	LITERAL1
+
+# ENUM VALUES
+ADS1115_ASSERT_AFTER_1	LITERAL1
+ADS1115_ASSERT_AFTER_2	LITERAL1
+ADS1115_ASSERT_AFTER_4	LITERAL1
+ADS1115_DISABLE_ALERT	LITERAL1
+ADS1115_LATCH_DISABLED	LITERAL1
+ADS1115_LATCH_ENABLED	LITERAL1
+ADS1115_ACT_LOW	LITERAL1
+ADS1115_ACT_HIGH	LITERAL1
+ADS1115_MAX_LIMIT	LITERAL1
+ADS1115_WINDOW	LITERAL1
+ADS1115_8_SPS	LITERAL1
+ADS1115_16_SPS	LITERAL1
+ADS1115_32_SPS	LITERAL1
+ADS1115_64_SPS	LITERAL1
+ADS1115_128_SPS	LITERAL1
+ADS1115_250_SPS	LITERAL1
+ADS1115_475_SPS	LITERAL1
+ADS1115_860_SPS	LITERAL1
+ADS1115_CONTINUOUS	LITERAL1
+ADS1115_CONTINOUS	LITERAL1
+ADS1115_SINGLE	LITERAL1
+ADS1115_RANGE_6144	LITERAL1
+ADS1115_RANGE_4096	LITERAL1
+ADS1115_RANGE_2048	LITERAL1
+ADS1115_RANGE_1024	LITERAL1
+ADS1115_RANGE_0512	LITERAL1
+ADS1115_RANGE_0256	LITERAL1
+ADS1115_COMP_0_1	LITERAL1
+ADS1115_COMP_0_3	LITERAL1
+ADS1115_COMP_1_3	LITERAL1
+ADS1115_COMP_2_3	LITERAL1
+ADS1115_COMP_0_GND	LITERAL1
+ADS1115_COMP_1_GND	LITERAL1
+ADS1115_COMP_2_GND	LITERAL1
+ADS1115_COMP_3_GND	LITERAL1
+ADS1115_BUSY	LITERAL1
+ADS1115_START_ISREADY	LITERAL1
\ No newline at end of file
diff --git a/src/ADS1115_WE.h b/src/ADS1115_WE.h
index c5a269a..c531368 100644
--- a/src/ADS1115_WE.h
+++ b/src/ADS1115_WE.h
@@ -70,8 +70,9 @@ typedef enum ADS1115_CONV_RATE{
 } convRate;
 
 typedef enum ADS1115_MEASURE_MODE{
-	ADS1115_CONTINOUS = 0x0000,
-	ADS1115_SINGLE    = 0x0100
+	ADS1115_CONTINOUS  = 0x0000, // keeping misspelled enum for backwards compatibility.
+	ADS1115_CONTINUOUS = 0x0000, 
+	ADS1115_SINGLE     = 0x0100
 } measureMode;
 
 typedef enum ADS1115_RANGE{
@@ -139,7 +140,7 @@ public:
     */
 	void setAlertPol(ADS1115_ALERT_POL polarity);
 
-	/* Choose maximum limit or maxium and minimum alert limit (window)in Volt - alert pin will
+	/* Choose maximum limit or maximum and minimum alert limit (window)in Volt - alert pin will
      * be active when measured values are beyond the maximum limit or outside the window
      * Upper limit first: setAlertLimit_V(MODE, maximum, minimum)
      * In max limit mode the minimum value is the limit where the alert pin will be deactivated (if
@@ -164,9 +165,9 @@ public:
     */
 	void setConvRate(ADS1115_CONV_RATE rate);
 
-	/* Set continous or single shot mode:
+	/* Set continuous or single shot mode:
      *
-     * ADS1115_CONTINOUS  ->  continous mode
+     * ADS1115_CONTINUOUS  ->  continuous mode
      * ADS1115_SINGLE     ->  single shot mode (default)
     */
 	void setMeasureMode(ADS1115_MEASURE_MODE mode);